Making a house for a cat with your own hands is more fun with your children. Just give preference to safe materials. So, the simplest and cheapest option for arranging a hut is as follows:

You need to take a large corrugated box. It is better that the box has parameters of at least 35 by 50 cm in width and up to 50 cm in height.
Now you need to prepare the tools at hand: scissors, glue, stationery knife, fine sandpaper, tape, pencil, colored paper, upholstery and more.
For the inner framing (bedding on the floor), you can use foam rubber. But if it is not available, an unnecessary blouse or a piece of an old blanket will do. Colored paper can be used for the exterior decoration of the house. But it is more relevant to use bouclé fabric or fur.
Now we start preparing the box itself. To do this, remove the stickers from it, glue the places where there are cracks with tape, cut off the burrs, grind the roughness with sandpaper.

The creative process brings joy not only to children

Draw a hole on the end of the box. To do this, put a saucer with a diameter of at least 20 cm to it and circle it around the edges. Then we cut a hole with a clerical knife. Gently sand the edges with sandpaper.
Once again we glue all the joints with tape or glue. The house should turn out to be durable so that the cat is comfortable and calm in it. Dry the product before starting the exterior finish.
Now we paste over the house with colored paper or textiles. For the second option, silicone quick-drying glue is suitable. In this case, you cannot use a furniture stapler, as the cat can injure itself from the inside of the paper clips.
Sew a small pillow of foam rubber and upholstery fabric to the size of the floor in the house.

6 House of newspaper tubes

Do not rush to hand over old newspapers for waste paper – you can also build a beautiful house for a cat from them. In addition to newspapers, you will need knitting needles or wire, glue and scissors.

First you need to form a lot of tubes: take a sheet of newspaper, grease one edge with glue and roll it into a tight tube. When the main building material is ready, start designing. Form a “sun” from knitting needles or wire, fastening the ends together, and braid with tubes. It turned out the foundation.

Bend the wire up and continue to braid, not forgetting to leave a gap for the entrance. The house should be large enough for the pet – take any object similar in size to the future “tenant” (for example, a ball) and put it in the middle of the structure. Finally, for reliability, open the structure with varnish.

Original houses

Any interior will be decorated with such original structures for pets:

from two captive baskets connected in the form of a pearl;
sewn of dense fabric in the shape of a cat: with ears, a tail, a hole in the shape of a yawning mouth;
from wooden cubes (walls can be decorated with colored paper);
mini wigwam;

in the form of a ball made of carpet (the opening of the dwelling can be decorated with a knitted scarf around the edges);
hanging fabric with a soft bottom, hanging anywhere;

egg-shaped with smooth and hard walls, thanks to the bedding from the inside;
vertical house with scratching posts on the sides and a sleeping place in the form of a cylinder in the center.

How to develop a structure

The preferences of cats and cats may differ. For example, cats prefer houses with two entrances – in case of emergency evacuation of offspring. Therefore, many people like pipes or structures similar to them. At the same time, they do not like too large a hole, since they need to feel like they are in a shelter. Therefore, the entrance / exit to the house must be made not too large so that the pet can easily pass into it, but no more. And one more thing: not all cats like houses that are on the floor – cats live in them with kittens. “Singles” prefer shelters at a height, although this is also not a fact, and depends on the habits of the individual.

For a cat with kittens, a house standing on the floor is suitable

Cats prefer to spend time at a height, watching everything that happens around them. They rarely sit in the house, but on the playgrounds they can lie for hours. If you have a cat, make more areas, and of solid size – so that the animal can lie stretched out to its full height without the risk of falling. Railings, if needed, are only for the highest shelves and obviously not around the perimeter, but only from the back and a little from the sides. In general, males feel great on playgrounds without any fences: there are no fences on the trees. Railings are needed more for the calmness of the owners than for cats.

The bottom floor is usually ignored

And by the way, there are cats who like to sit on the playgrounds no less than cats. So they also need vantage points, as well as cat houses. You never know, maybe he will be in a bad mood and he will decide to hide from you there. So yes, we did not simplify the task with the choice, but this is exactly the case – until you try it, you will not understand what your pet needs.

Photo with dimensions

No matter how much they talk about the device of a house for a cat, it is best to understand the dimensions with drawings with dimensions. If you look at them closely, you will notice a solid take-off run. This is understandable – cats are large and small, respectively, and the size of the cat’s house will be larger / smaller. You can adjust them yourself depending on the size of your pets or the available space.

Photo of cat houses with dimensions

Three options for cat corners with sizes

The height of the structures presented is rather big – 180 cm and higher, but you can reduce it by removing the floors that are unnecessary in your opinion. All these dimensions can be taken as a basis to develop your own layout, put down approximate dimensions. Having a drawing in hand, you can start purchasing materials and manufacturing.

Building a house for a cat

First, we will make the house itself. To do this, take two sheets of chipboard and, having drawn a semicircle or a truncated circle, cut out two identical semicircles with a jigsaw or a saw according to the drawing. One semicircle will be solid, and on the other we will cut out circles that imitate the footprint of a cat’s paw. You can see how to do this in a step-by-step photo on the Internet.

Now you need to prepare the slats, cut them so that they are of the same length, shave off the excess protrusions.

From one corner of the truncated circle, make seven marks at the same distance, so that the latter is just at the second corner of the semicircle of the chipboard sheet. Do the same with the other sheet. Make sure that all the marks of both blanks coincide with each other.

Now insert the prepared strips between the two truncated circles, the ends of the strips should touch the marks on the sheets. Using a screwdriver, screw the slats to the chipboard sheets along the entire circumference. Only the base of the truncated circle will remain. Now you can upholster our house with the selected fabric. This can be done with a glue gun or fabric stapler. How to properly upholster a house, you can see in a detailed master class.

Measure the resulting base of the future house and transfer the drawing to a sheet of fiberboard, which was prepared for the foundation of our pet house. Glue a piece of foam rubber cut according to the drawing to the resulting place. This will be the first bed for the cat.

Leave space on the base sheet for the pipe, which you want to use as a scratching post and make an additional bed for the animal on top. Now you can upholster the main sheet with fabric. Make a hole in the upholstery as in the base.

After measuring the diameter of the pipe, cut a circle with an identical diameter in the sheet so that the pipe goes into the circle and stands firmly there. Next, you need to squeeze the prepared wooden blocks into the pipe. This is done in order to be able to fix a second bed at the end of the pipe, as well as to ensure greater stability of the pipe.

Cut out two semicircles of the same size from two sheets of chipboard and fiberboard. In the chipboard sheet, cut out a circle for the pipe, and the fiberboard sheet will remain the same.

Now a semicircle made of chipboard must be “put on” on the upper part of the pipe and fixed with hot glue. Place the second semicircle on top and attach to the bar in the pipe using a screwdriver or drill. Now you can glue a piece of foam rubber for softness and upholstery with a second bed.

Use hot glue to wrap the string around the pipe from top to bottom. Secure with glue or stapler. The first scratching post is ready.

Wrap the finished small board with a thick cloth or also wrap it with rope. Lean against the roof of the cat house. Secure with screws at the base and roof. Here is the second scratching post!

Using a stapler, you can attach a rope with a ball at the end to the upper couch. This will be a toy for the cat.

The house for the cat is ready, it remains to determine the place where the kingdom of your pet will be located in the apartment.

# 2. House made of plywood

A real mansion where all the dolls can be accommodated is a dream for many children, especially girls.

If you know how to tinker and have a little free time, then you can build a realistic house for dolls from plywood, as did the Joker from yaplakal.com. The author did it in one week.

For work, you will need the following materials:

two 8 mm plywood sheets;
jigsaw;
furniture carnations;
acrylic sealant;
hot melt adhesive;
pieces of linoleum and wallpaper;
acrylic paint.

Instructions on how to make a do-it-yourself dollhouse from plywood:

1 A construction scheme is being developed. A simplified plan of a real house can be taken as a basis. It is important to correctly calculate the proportions so as not to be mistaken in size.

2 Next, you need to make markings on plywood and cut out the component parts along it.

3 The structure is assembled on small diameter furniture nails. For reliability, you can coat the seams with acrylic sealant, this technique will add strength to the structure.

4 The house is quite large in size. Dimensions: height – 1000 mm; width – 1100 mm; depth – 400 mm.

5 Next, the structure must be pasted over with suitable wallpaper. For exterior decoration, wallpaper imitating brickwork is suitable. The outer roof top can be left unchanged.

6 Inside, the house is pasted over with the remnants of paper wallpaper, and the ceiling is painted with acrylic paint to match.

7 Linoleum is glued to the floor with hot glue. If you do not have any linoleum residues, then thick wallpaper or fabric suitable for the floor will do. You can also arrange carpets instead of carpet or linoleum.

8 Doll furniture can be purchased from the dedicated toy shops.

9 Home lighting with LED lamp:

10 In the house, you can make rooms to your liking: for example, a bathroom, living room, kitchen, bedroom, etc. depending on the furniture purchased.

A house with such dimensions will perfectly fit Barbie dolls and smaller doll models.

Tools and materials for work

You can first choose the material for making a cat house with your own hands, and only then find the necessary tools.

A wooden cat house is the most difficult and time consuming, but very practical and durable. To make it, you need a regular saw, screws and a screwdriver.

But it is better if the master has a different, more universal set of tools at his disposal:

electric jigsaw;
screwdriver or drill;
furniture stapler and large staples;
glue gun;
corner and ordinary clamps;
tape measure and a set of rulers – simple and angular;
stationery knife and scissors;
self-tapping screws, metal corners, staples, universal glue for wood and fabric.

The walls and roof are made of thick plywood or chipboard, and the external and internal pasting is made with strong furniture upholstery – it is dense, has a long service life and resists sharp claws well. With such a set, it is quite possible to build a house for a cat in 1-2 days.

The most budget-friendly option for a cat house is thick cardboard. You can take new sheets and adapt the remaining packaging from large household appliances (refrigerators, TVs, stoves) for the project.

Corrugated boxes keep their shape perfectly, can be easily cut and glued. A set of accessories for such a house:

sharp knife and scissors;
Ruler and pencil;
glue;
stationery stapler.

A sketch and a diagram of a house for a cat can be drawn directly on the material and immediately cut along the outlined lines.

Fabric-foam lodge. It requires the least tools, and women’s hands will cope with the work in a matter of hours. But a sewing machine capable of processing edges and joining several layers of dense fabric is required. To insert the foam filler, you need to provide for detachable zippers, since it will have to be periodically pulled out and disinfected.

Fabric houses can be quite simple, without wide internal elements. To do this, you will additionally need thin wooden slats, and the design will be very similar to a camping tent or an Indian wigwam. A soft house for a cat, which you can make with your own hands, usually turns out to be author’s – each owner comes up with something individual for his pet.

There are also quite exotic ways of arranging a cat’s house. For example, weaving from newspaper tubes. The result is a kind of a basket of arbitrary shape – it all depends on the imagination and the time spent. But the hard bottom in the house will still have to be covered with a soft foam mat or other dense mattress.

The first house

I recommend practicing on a small one-room house. Then it is not so a pity to throw it away, and the children quickly get bored with everything. Look how cute and cozy they are, albeit small. Pictures are enlarged by clicking.

But what a little cute house, even without wallpaper, it already looks dignified, but what if you hang curtains, throw a couple of pillows, lay a carpet? By the way, the easiest way to make carpet and pillows is from felt. And it is not necessary to sew! Felt is easy to glue with a moment or a hot gun.

Manufacturing process:

Step 1.

On the small valves of the box, mark the middle and draw lines to the bases of the valves. We teach an isosceles triangle.

Step 2.

Work for scissors: cut off the unnecessary part from the upper small valves along the drawn line. We cut off all the lower valves, but do not throw them away. We will need them for the roof.

Step 3.

We make the roof. We glue the lower large valves with tape. These valves will be the top of the roof.

Step 4.

We fix the roof into a single structure with masking tape.

Step 5.

We cut out the roof for the roof from the corrugated cardboard sheet to give greater strength. We glue the roof with PVA glue on the roof.

Step 6.

On one long and one short side of the house we draw windows and cut them out with a clerical knife.

Step 7.

On the second long side of the house we draw a door and also cut it out with a clerical knife.

The house is ready! The facade of the house can be decorated with colored cardboard or painted with your child by hand.

← Armchair made of corrugated cardboard with your own hands Lightbox from a cardboard box and Whatman paper →

How to make a decorative house for interior decoration

A cardboard tea house is a good idea for a kitchen that will delight you and interest guests, they will definitely appreciate this idea. They can often be found in the home store, but not worth spending your money on. You can do it yourself and spend only time on it.

First you need to take cardboard and make a layout of the future walls and roof for the future house. For roofs, cut two pieces 8 * 13 cm.The floor will be 13 by 12, and the walls will be 17.5 by 9.6 cm.

We need to make two more walls, to which we need to add a triangle for the size of the roof. And on the front wall, cut out a round window and a semicircular hole at the bottom, so that it is convenient to take out tea bags. This can be done neatly with a utility knife.

To make the cardboard artwork and decor look better, paint the front side of the cardboard with white paint and let it dry. After that, carefully connect the parts and glue them together. Do not forget to make the base of the house beautiful.

Making a cat shelter

In addition to children, a family or a single person is often content with a cat or cat. Such a pet should also not be left without due attention when there is so much cardboard around. One box is enough if its width, length and height are at least 400x400x500 mm. In an appropriate container, the pet will feel comfortable when observing:

A passage originating from the floor so that the animal does not cling to the edge;
Soft flooring so that the pet can rest;
Dark space (cats and cats see and feel great at night).

Therefore, a cardboard house for a cat should provide a minimum of holes – one and only for the passage. An exception is playgrounds for cats, which are made up of several boxes with two or three holes.

[

] (https://podelki.expert/wp-content/uploads/2020/04/kak-sdelat-domik-iz-kartona-25.jpeg )

[

] (https://podelki.expert/wp-content/uploads/2020/04/kak-sdelat-domik-iz-kartona-26.jpeg )

Houses made of bushings, paper

A pyramid house is made from toilet paper rolls – ten pieces are needed. They need to be glued to each other, to accommodate the “inhabitants” of the kinder surprises there. If desired, it will come out to minimalize the interior by cutting out cardboard circles, depicting the situation on them. The outer part is pasted over with “snow” made of white felt, cotton wool, padding polyester or painted with silver spray paint. If there are more than three bushings, they build a whole night metropolis. For this, the details are painted with dark paint, leaving only light rectangles of the windows. Windows can also be cut out of foil or painted with glitter paint. To make a candlestick house, the windows are cut through so that the flame can be seen. An equally interesting idea is the elven town. The tops of the bushings are bent with two fingers to form an angle, the structure is slightly flattened. A bright, almost flat roof is made from a square twice folded in half, which is put on a base from a sleeve. The house is decorated with a window, a door, and snow on the roof.

The New Year’s city will be guarded by “winter” characters – Santa Claus, deer, hares, snowmen, also made of cardboard sleeves.

Backlit houses

Making a cardboard “building” with LEDs will create a real “magical” design, such a structure looks especially interesting in the evening. If the structure is large, such as a children’s playhouse, the easiest way is to illuminate it with a lamp on a clothespin or an LED strip plugged into an outlet. It is only important to place the device so that the probability of hitting and breaking it is minimal. The winter dollhouse is also illuminated, with light being conducted into each room. To create lighting, segments of LED strip, a power supply are used. On the back wall of the house there are switches that allow you to light each room separately. It’s even more fun to build a whole magical city. For work you will need:

a stand is a simple thick cardboard that is placed on a table, bedside table, window sill, or any other surface where the composition will be placed;
blanks for houses – boxes of tea, milk, juices, shoes, etc .;
paints – acrylic, gouache, watercolor;
paper – white and several bright colors;
snow – it is made from polystyrene, cotton wool, padding polyester, paper napkins, or they buy dry imitation in bags, liquid – in cylinders;
the lighting itself – a strip of LEDs, a Christmas tree garland, separate colored bulbs with stands powered by batteries;
the inhabitants of the town – figurines of animals, men, snowmen, Snow Maiden, Santa Claus of the appropriate size.

The city sometimes makes lanterns along the paths, glowing signs, etc.

Sources used and useful links on the topic: https://krrot.net/dom-dlya-koshki-svoimi-rykami/ https://modernplace.ru/domik-dlya-koshki/ https://lafoy.ru/domik- dlya-koshki-svoimi-rukami-11-idey-foto-20 https://MrKot.com/domik-dlya-koshki-svoimi-rukami https://stroychik.ru/raznoe/domik-dlya-koshki https: / /gidrukodeliya.ru/domik-dlya-koshki-svoimi-rukami https://babyplayroom.ru/igry/domik-dlya-kukol-svoimi-rukami.html https://litbro.ru/poleznoe/domik-dlya-koshki -svoimi-rukami https://daynotes.ru/domik_dlya_kukol_iz_korobki_svoimi_rukami/ https://www.utupack.ru/other/livehacks/domik-iz-kartonnoj-korobki/ https://mirrukodelija.ru/domik-iz-kartami/ https://podelki.expert/kak-sdelat-domik-iz-kartona/ https://roomester.ru/dekor/svoimi-rukami/domik-iz-kartona.html

Post source: lastici.ru